400G DR4 and FR4 Optical Modules for Data Center Interconnects

David Aug 11, 2026 ◉ 476 views

1. Introduction

In today’s digital era, data centers are experiencing unprecedented demand for high-speed, high-bandwidth, and low-latency network solutions. For 400G single-mode fiber applications exceeding 100 meters in transmission distance, 400G DR4 and 400G FR4 optical modules have emerged as the two dominant and critical technical solutions.

This blog delves into the technical specifications, core differences, and typical connection methods of 400G DR4 and 400G FR4 optical modules. By thoroughly analyzing their working principles and application scenarios, AICPLIGHT aims to help you better understand their roles and value in modern data center interconnect architectures.

2. What is a 400G DR4 Optical Module?

The 400G DR4 optical module is a transceiver that achieves 400G transmission using Parallel Single-Mode Fiber (PSM) technology. It employs four independent 100G PAM4 signal channels, each operating at the same 1310nm wavelength. At the transmitter end, an integrated laser array drives the four optical signals, which are then transmitted via an MPO-12 APC multi-fiber connector.

This module supports two typical transmission distances: 500 meters and 2 kilometers. AICPLIGHT offers IEEE-compliant 400GBASE-DR4 (500m) and the extended-reach version 400GBASE-XDR4 (2km).

400G OSFP-DD DR4 schematic showing a 400GAUI-8 interface, PAM4 gearbox, laser and PIN blocks, and four 1310 nm TX/RX paths to an MPO-12 APC connector.

400G QSFP-DD DR4 Schematic

400G OSFP DR4 schematic with a 400GAUI-4 interface, 4 x 100G PAM4 ASIC, laser and PIN blocks, and parallel 1310 nm channels to an MPO-12 APC connector.

400G OSFP DR4 Schematic

3. What is a 400G FR4 Optical Module?

The 400G FR4 optical module utilizes Wavelength Division Multiplexing (WDM) technology. Its core mechanism combines four distinct wavelengths (1271nm, 1291nm, 1311nm, and 1331nm) into a single composite optical signal via a multiplexer (MUX).

At the receiving end, a demultiplexer (DEMUX) separates the composite signal back into the original four channels. Unlike DR4, FR4 utilizes a duplex LC UPC interface, requiring only two single-mode fibers (one transmit, one receive), significantly conserving fiber resources.

400G QSFP-DD FR4 schematic showing four PAM4 channels converted into 1271, 1291, 1311, and 1331 nm wavelengths through MUX and DEMUX blocks.

400G QSFP-DD FR4 Schematic

400G OSFP FR4 schematic showing a 400GAUI-4 interface, 4 x 100G PAM4 ASIC, WDM wavelength paths, and a duplex LC UPC connector.

400G OSFP FR4 Schematic

4. 400G DR4/XDR4 vs 400G FR4

Parameter400G DR4/XDR4400G FR4
TechnologyParallel optics (4×100G PAM4)WDM (4 wavelengths combined)
Fiber Count8 fibers (MPO-12)2 fibers (LC duplex)
ConnectorMPO-12 APCLC UPC
Wavelengths4×1310nm (identical channels)1271nm/1291nm/1311nm/1331nm
Distance500m (DR4), 2km (XDR4)2km
Use Cases• 400G point-to-point
• 4×100G breakout
400G point-to-point (fiber-efficient)

5. Connection Solutions

5.1 400G Direct Connection Solution

Three 400G direct links compare DR4, XDR4, and FR4 modules using MPO-12 APC trunk cables or a duplex LC UPC fiber patch cable.

Both 400G DR4/XDR4 and 400G FR4 support 400G-to-400G links. However, their differing optical interfaces require specific fiber cables:

  • 400G DR4/XDR4: Uses MPO-12 trunk cables.
  • 400G FR4: Uses duplex LC patch cables.

Cost Note: At the same transmission distance, MPO-12 cables are more expensive than LC duplex cables.

5.2 400G Breakout Solution

400G DR4 and XDR4 breakout links split from one MPO-12 APC side into four duplex LC UPC branches connected to 100G DR or FR modules.

A key advantage of 400G DR4/XDR4 lies in its interoperability with 100G single-wavelength optical modules. This enables compatibility with equipment scenarios requiring high-density connections, achieving 1-to-4 branch connections.

6. Conclusion

The 400G DR4/XDR4 and 400G FR4 modules embody two foundational technologies:

  • DR4/XDR4: Parallel optics for flexible breakout and short-to-mid-reach scalability
  • FR4: WDM for fiber efficiency and 2km reach

They have become core components for constructing efficient, scalable interconnect architectures in today’s hyperscale data centers.